• Home
  • Blog
  • About
  • Privacy Policy
Menu

James Goodwin

  • Home
  • Blog
  • About
  • Privacy Policy

Green cherry wood burl bowl

November 17, 2026

After the last two practice pieces from green cherry wood I decided to try turning something out of one of the blanks cut from the burl proper. I chose the least promising blank which was the cap of one of the burl sections about 10 inches in diameter and about 3 inches thick. You can see the chunk below, it is the part below the red line on image.

I could have tried turning it as a live edge bowl with the bark as the top but I could already see a big bark inclusion hole on the cut side so I decided to make that the top and mostly turn that hole away. I was a little preoccupied with this one so I don’t have a lot of in progress photos. I drilled a 2 1/4” x 3/8” recess in the center of the flat side and mounted it on the lathe chuck and used the live center in the tail stock for stability.

Removing the bark shoots bark all over the room and starts out very rough turning. I used a 1/2” spindle gouge for most of the rough turning and that worked pretty well. I eventually got down to mostly wood, though with considerable areas of bark inclusion. I got a nice shape on the outside and cut a tenon on the bottom so I could hold it in the chuck for hollowing. I sanded the outside to 320 grit.

I turned it around in the chuck and I proceeded to hollow the interior of the bowl. As I got close to 1/2” thickness over all some of the bark inclusion chunks came out and there were some holes, fortunately they were non structural and cool looking holes. I sanded the interior of the bowl to 320 grit.

I took the bowl off the lathe and buried it in the desiccant beads for three days. Here’s what it looked like right off the lathe.

View fullsize PXL_20261109_170458872.jpg
View fullsize PXL_20261109_170506057.jpg
View fullsize PXL_20261109_170509976.jpg

The drying went really well, I fully expected the tenon would cause the bottom to crack because it was twice as thick as the sides but it didn’t. I cut the tenon off with a flush cut saw and sanded the bottom of the bowl to 320 grit.

I then applied a coat of shellac based sanding sealer and let that cure over night. The next day I sanded it again with 400 grit and then put a second coat of shellac on it to stabilize and harden some of the softer areas. It also darkened the bark inclusions considerably which looked great. The next day I sanded it up to 1000 grit and then applied Thompson Butcher Block Conditioner to the bowl. Here’s the finished item.

View fullsize PXL_20261114_141541083.PORTRAIT.jpg
View fullsize PXL_20261114_141603151.PORTRAIT.jpg
View fullsize PXL_20261114_141622878.PORTRAIT.jpg

I really like how it came out, clearly not going to hold soup but still a very nice artistic bowl that is very usable.

In Journal Tags building, green wood turning, cherry burl, cherry burl bowl
Black Phillip Halloween Costume →

Latest & Greatest

Blog RSS
Featured
PXL_20261114_141451424.jpg
November 17, 2026
Green cherry wood burl bowl
November 17, 2026
Read more →
November 17, 2026
PXL_20261031_221812613.jpg
November 2, 2026
Black Phillip Halloween Costume
November 2, 2026
Read more →
November 2, 2026
PXL_20261020_150958971.jpg
October 27, 2026
Green wood turning...
October 27, 2026
Read more →
October 27, 2026
misc-bowls.jpg
September 4, 2026
Hollow form bowl, plate, small walnut snack bowl, and re-turning my first lidded bowl...
September 4, 2026
Read more →
September 4, 2026
PXL_20260826_150938765.jpg
August 26, 2026
Walnut Bowls
August 26, 2026
Read more →
August 26, 2026
PXL_20260814_121041091.jpg
August 14, 2026
Wider, Lower, More Curved Segmented Bowl
August 14, 2026
Read more →
August 14, 2026
PXL_20260801_152456504.jpg
August 3, 2026
Segmented Bowl
August 3, 2026
Read more →
August 3, 2026
PXL_20260709_231900182.jpg
July 15, 2026
Learning to Turn
July 15, 2026
Read more →
July 15, 2026
PXL_20260531_111209154.jpg
May 31, 2026
Record Sorter
May 31, 2026
Read more →
May 31, 2026
PXL_20260324_141508528.jpg
March 25, 2026
Set of folding side tables
March 25, 2026
Read more →
March 25, 2026

Tags

  • building
  • journal
  • projects
  • python
  • software

All content on this site is Copyright 2007-2024 by James Goodwin unless otherwise noted.